DIY MARQUEE LIGHTS
Updated: Apr 12, 2019
Hey all, I’m Dani and welcome to Coral Channel - If you’re looking for a super trendy way to light up your space and make it look super amazing, then these DIY MARQUEE DECOR LIGHTS are for you!
They are easy to make and add a touch of personality to any room in your home.
And guys, if you’re not already subscribed to coral, share some love and click subscribe and turn on those bell notifications because we have a lot of really exciting content coming up on our channel - that include me and you’re not going to want to miss it.
Pine Shop Shelving Board (12x36): https://amzn.to/2LjEVfF
11X17 Stencil Shape
Jig Saw: https://amzn.to/2BBQgbj
80 Grit 5” Disc Sandpaper: https://amzn.to/2wgNfaD
Orbiter Sander: https://amzn.to/2BEKO7C
Drill Bit 1: 3/8: https://amzn.to/2o2G2Hw
Drill Bit 2: 1/8: https://amzn.to/2o2G2Hw
Drill Bit 3: 7/32: https://amzn.to/2o2G2Hw
Drill Bit: 4: 3/32: https://amzn.to/2o2G2Hw
Dremel Kit *Optional: https://amzn.to/2Mq4UY5
Scrap Wood: https://amzn.to/2nYQn7b
Paint or Wood Stain: https://amzn.to/2nYfSFE
Battery operated String Lights: https://amzn.to/2Ll68yr
Glue Gun: https://amzn.to/2nYwUTY
¼” robertson screwdriver: https://amzn.to/2MtruPM
5 ¾ wood screws: https://amzn.to/2Li68PO
Step 1: CUT IT OUT
Take your Coral stencil print and cut out the shape using scissors.
Step 2: IT’S A TRACE!
Trace the stencil print onto your 12X36 pine board using a pencil.
Step 3: GET’N JIGGY WITH IT
Make holes at the inside curves using a 3/8th drill bit.
Using your Jig Saw, carefully cut out your stenciled design. Don’t worry about rough edges, all this can be fixed later using your sander.
Step 4: MAP IT OUT
Now it’s time to map out where you want your lights to go. You’ll want to make sure not to mark too close to the edge so that you don’t split the wood when you’re drilling. Try to mark about 1 inch from the edge as a safeguard.
Step 5: IT’S A HOLE THING
Once you’re happy with the marks, fasten your board to your table using a clamp and a scrap piece of wood underneath. The scrap wood will help avoid unnecessary blow out from the wood. You’ll want the good side of your board facing down.
Take your small ⅛ drill bit and drill all the holes.
Once your holes are completed, take your larger 7/32 drill bit and drill the holes through again. This way, it’s clean and large enough to fit your lights.
Step 5: SAND AWAY!
Time to Sand! Sand your entire project to your liking. This is a part to have fun, round off edges etc. The goal of the sanding is to leave your project feeling nice a smooth.
Step 6: ADD COLOR TO YOUR LIFE
Colour Time! I opting to keep some of the wood grain in my project, so i’m using a coloured stain with painted accents on top. Let Dry.
You could opt to add a finish on your piece to ensure it can handle a bit of day to day scuffs. This is completely optional.
Step 7: LIGHT UP YOUR LIFE
Add your string lights and use a glue gun in the back to hold your lights in place and all the excess cords in place.
Step 8: IT’S ALIVE, IT’S ALIVE!
Light it up and enjoy!
Let me know what projects you would like to see on the channel in the comment section below!